ACS712 Current Sensor 30Amp
- Product Code: 902
- Availability: 5
Shipping : Same day dispatch for Most orders if payment done before 4pm. Delivery Normally takes 2 to 5 working days depending upon your location.
If you require more quantity than what is currently in stock or you want to buy in bulk quantity e-mail us your requirements on: dnatechindia "at" gmail.com
ACS712 Current Sensor
Hall effect current Sensor with Maximum rating of 30 Ampere
The Allegro™ ACS712 provides economical and precise solutions for AC or DC current sensing in industrial, commercial,and communications systems. The device package allows for easy implementation by the customer. Typical applications include motor control, load detection and management, switch mode power supplies, and over current fault protection. The device is not intended for automotive applications.
The device consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage. Device accuracy is optimized through the close proximity of the magnetic signal to the Hall transducer. A precise, proportional voltage is provided by the low-offset,chopper-stabilized BiCMOS Hall IC, which is programmed for accuracy after packaging.
Allegro ACS712 current Sensor device which provides an economical and precise way of sensing AC and DC currents based on Hall-effect. This is a breakout board for the fully integrated Hall Effect based linear ACS712 current sensor. The sensor gives precise current measurement for both AC and DC signals. Thick copper conductor and signal traces allows for survival of the device up to 5 times over current conditions.Compatible with arduino and since its output is analog it can be directly interfaced to PIC controllers, AVR & ARM processors as well.
The ACS712 outputs an analog voltage output signal that varies linearly with sensed current. The device requires 5 Volt DC for VCC and a couple of filter capacitors. Please keep in mind that though the ACS712 is rated for 2.1kV isolation, the PCB it is on is not designed for that type of voltage. Please keep that in mind if you are using this breakout in high voltage applications.
Features and Benefits
- 5 μs output rise time in response to step input current
- 80 kHz bandwidth
- Total output error 1.5% at TA = 25°C
- 1.2 mΩ internal conductor resistance
- 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- 5.0 V, single supply operation
- 100 mV/A output sensitivity
- Output voltage proportional to AC or DC currents
- Factory-trimmed for accuracy
- Extremely stable output offset voltage
- Nearly zero magnetic hysteresis
- Ratiometric output from supply voltage
ACS712 Current Sensor Hall effect current Sensor with Maximum rating of 20 AmpereThe Allegro™ A..
Rs.295.00 (inc GST) Rs.330.40
ACS712 Current Sensor Hall effect current Sensor with Maximum rating of 5 AmpereThe Allegro™ AC..
Rs.295.00 (inc GST) Rs.330.40
4020 14-stage binary counterThe HEF4020B is a 14-stage binary counter with a clock input (CP), an ov..
Rs.18.88 (inc GST)
PIC12F508 MicrocontrollerThe PIC12F508 devices from Microchip Technology are low-cost, high-performa..
Rs.60.18 (inc GST)
• Photo detector and preamplifier in one packa..
Rs.33.04 (inc GST)
CP2102 SMD USB-to-TTL Bridge ControllerThe high-performance, low cost CP21xx USB to UART bridge fami..
Rs.159.30 (inc GST)
MCP2515 CAN BUS Module BoardThis is a easy to use CAN bus module controlled via SPI Interface. It co..
Rs.708.00 (inc GST)
6 Pin Relimate SHS Straight ConnectorRelimate connector are one of the most widely used connectors i..
Rs.15.05 (inc GST)
4047 Monostable - Astable multivibratorThe CD4047B is capable of operating in either the monost..
Rs.23.60 (inc GST)
12V Relay Board 8 ChannelThis is a relay board with 8 high current relays. It is ideal board to cont..
Rs.342.20 (inc GST)