Attention !!! We are shipping orders now but due to Covid-19 situation it can take 1-2 days for your orders to be shipped from our Nashik warehouse. If you have any queries feel free to contact us. Thank you for your support and understanding.
  • 8412906903
  • dnatechindia@gmail.com

Product Images are shown for illustrative purposes only and may differ from actual product.

X9c103s Digital Potentiometer Module

  • Stock: Out Of Stock
  • SKU: 1617 | DAB057
  • Rs. 236.00 (inc GST)
    Rs.200.00 + GST

    Qty :

GST Invoice on all Purchase. So you will be eligible to take input tax credit.

IF component not in Stock or require more quantity or want to buy in bulk e-mail us your requirements on: dnatechindia "at" gmail.com.

Shipping : Due to Covid-19 situation delivery will be affected. Delivery period due to covid-19 issue will be from 4 - 12 days depending upon your location.

X9c103s Digital Potentiometer Module 

Digital potentiometer - it is a variable resistor whose resistance vale can be varied digitally from an Arduino or a Rasberry Pi.

It consists of a 3 pin output which can replace a mechanical potentiometer which has 3 pins and lets you vary its resistance digitally! This digital potentiometer can also store the current position after a power off in non volatile memory and start from the same position on power on. 
This Module is a breakout board for Intersils X9C103 digitally controlled potentiometer IC. This is DC 3-5V X9C103S Digital Potentiometer Board Module for Arduino. The X9C103 are digitally controlled (XDCP) potentiometers. Dc3v-5v X9c103s Digital Potentiometer consists of a resistor array, wiper switches, a control section, and non-volatile memory. The wiper position is controlled by a three-wire interface. The potentiometer is implemented by a resistor array composed of 99 resistive elements and a wiper switching network. Between each element and at either end are tap points accessible to the wiper terminal.
The position of the wiper element is controlled by the CS, U/D, and INC inputs. The position of the wiper can be stored in non-volatile memory and then be recalled upon a subsequent power-up operation. The device can be used as a three-terminal potentiometer or as a two-terminal variable resistor in a wide variety of applications ranging from control to signal processing to parameter adjustment.
There are three sections of the Dc3v-5v X9c103s Digital Potentiometer as the input control, counter and decode section; the non-volatile memory; and the resistor array. The input control section operates just like an up/down counter. The output of this counter is decoded to turn on a single electronic switch connecting a point on the resistor array to the wiper output. Under the proper conditions, the contents of the counter can be stored in non-volatile memory and retained for future use. The resistor array is comprised of 99 individual resistors connected in series. At either end of the array and between each resistor is an electronic switch that transfers the potential at that point to the wiper.
The wiper, when at either fixed terminal, acts like its mechanical equivalent and does not move beyond the last position. That is, the counter does not wrap around when clocked to either extreme. The electronic switches on the device operate in a “make-before-break” mode when the wiper changes tap positions. If the wiper is moved several positions, multiple taps are connected to the wiper for tIW (INC to VW/RW change). The TOTAL value of the device can temporarily be reduced by a significant amount if the wiper is moved to several positions. When the device is powered-down, the last wiper position stored will be maintained in the non-volatile memory.
When power is restored, the contents of the memory are recalled and the wiper is reset to the value last stored. The internal charge pump allows a wide range of voltages (from -5V to 5V) applied to XDCP terminals yet given a convenience of the single power supply. The typical charge pump noise of 20mV at 850kHz should be taken into consideration when designing an application circuit.

We have Various sizes of Misc Modules. Check out our complete collection of Misc Modules


If you are in Nashik you can buy this Electronic Component at our local shop at New CBS, Nashik or you can place order online and get it delivered at your doorstep anywhere in India.

Specifications and Features

  • Simple 3 pin interface to control the resistance!
  • Supply voltage: 3V-5V
  • Chip: X9C103S
  • PCB board size: 2.7 * 1.3CM
  • 10K span potentiometer.
  • Potentiometer center tap between 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
  • VL and VH digital potentiometer sliding rheostat port corresponding to the low-end and high-end, allowing the input voltage range -5V to + 5V.

Package includes

  • 1 x Dc3v-5v X9c103s Digital Potentiometer Module for Arduino

Related Links

Reviews (0)

Write a review

Note: HTML is not translated!
    Bad           Good

NEW Products

Product Page : New Products

Humidity & Temperature Sensor Case

Humidity & Temperature Sensor Case

Humidity & Temperature Sensor plastic Box60x27x16 mm black plastic temperature sensor case humid..

Rs.120.36 (inc GST)
Rs.102.00 + GST

SKU: 2770 | DAE106
Stock: 5
USB A Male To USB A Female With Panel Mount

USB A Male To USB A Female With Panel Mount

USB A male to USB A Female With Panel Mount Clamp USB A male to Panel Mount USB A FemaleThis is a U..

Rs.129.80 (inc GST)
Rs.110.00 + GST

SKU: 2759 | DAE307
Stock: 0
TP5100 Lithium battery charge management IC

TP5100 Lithium battery charge management IC

TP5100 step-down 8.4V / 4.2V single lithium battery charge management ICTP5100 2 Ampere sw..

Rs.61.95 (inc GST)
Rs.52.50 + GST

SKU: 2718 | DAE254
Stock: 40
4 Pin Wire to Wire SM Connector (2517/2518)

4 Pin Wire to Wire SM Connector (2517/2518)

4 PIN Wire to Wire (AIR) connector 2517/2518 Series2517/2518 4 Pin JST SM AIR Connector with 2.54 mm..

Rs.20.77 (inc GST)
Rs.17.60 + GST

SKU: 2751 | DAE288
Stock: 49

Have You Seen

Product Page : Have You Seen

AD711 BiFET Opamp

AD711 BiFET Opamp

AD711 BiFET OpampAD711 Low Cost BiFET OPAMPThe AD711 is a high speed, precision monolithic oper..

Rs.200.60 (inc GST)
Rs.170.00 + GST

SKU: 0456 | DAA013
Stock: 1
TC426 High-Speed Power MOSFET Drivers

TC426 High-Speed Power MOSFET Drivers

TC426 High-Speed Power MOSFET DriversThe TC426/TC427/TC428 are dual CMOS high-speed drivers. A TTL/C..

Rs.130.98 (inc GST)
Rs.111.00 + GST

SKU: 0739 | DAA029
Stock: 0
STM32F103C8T6 ARM Development Board

STM32F103C8T6 ARM Development Board

STM32F103C8T6 ARM Development BoardDev Board for ARM Microcontroller – STM32F103C8T6This board is lo..

Rs.910.00 (inc GST)
Rs.771.19 + GST

SKU: 0626 | DAB048
Stock: 20
GY-906 MLX90614ESF MODULE

GY-906 MLX90614ESF MODULE

GY-906 MLX90614ESF MODULE GY-906-MLX90614ESF-New-MLX90614-Contactless-Temperature-Sensor-Module-Com..

Rs.1,314.52 (inc GST)
Rs.1,114.00 + GST

SKU: 2391 | DAC227
Stock: 10

Related Products

MCP41010 8-Bit Digital Potentiometer

MCP41010 8-Bit Digital Potentiometer

MCP41010 8-Bit Digital PotentiometerThe MCP41010 is a single-channel, 8-bit digital potentiometer fe..

Rs.177.00 (inc GST)
Rs.150.00 + GST

SKU: 0650 | DAA047
Stock: 0
X9C104 Digital Potentiometer Module

X9C104 Digital Potentiometer Module

X9C104 Digital Potentiometer ModuleThis Module is a breakout board for Intersils X9C104 digitally co..

Rs.295.00 (inc GST)
Rs.250.00 + GST

SKU: 1609 | DAB058
Stock: 5