• 8412906903
  • dnatechindia@gmail.com

Product Images are shown for illustrative purposes only and may differ from actual product.

X9c103s Digital Potentiometer Module

  • Product Code: 1617
  • Availability: 5
  • Price :

    Rs.247.80 (inc GST)

    Qty :

GST Invoice on all Purchase. So you will be eligible to take input tax credit.

IF component not in Stock or require more quantity or want to buy in bulk e-mail us your requirements on: dnatechindia "at" gmail.com.

Shipping : Same day dispatch for Most orders if payment done before 4 pm. Delivery Normally takes 2 to 7 working days depending upon your location.

X9c103s Digital Potentiometer Module 

Digital potentiometer - it is a variable resistor whose resistance vale can be varied digitally from an Arduino or a Rasberry Pi. It consists of a 3 pin output which can replace a mechanical potentiometer which has 3 pins and lets you vary its resistance digitally! This digital potentiometer can also store the current position after a power off in non volatile memory and start from the same position on power on. 

This Module is a breakout board for Intersils X9C103 digitally controlled potentiometer IC. This is DC 3-5V X9C103S Digital Potentiometer Board Module for Arduino. The X9C103 are digitally controlled (XDCP) potentiometers. Dc3v-5v X9c103s Digital Potentiometer consists of a resistor array, wiper switches, a control section, and non-volatile memory. The wiper position is controlled by a three-wire interface. The potentiometer is implemented by a resistor array composed of 99 resistive elements and a wiper switching network. Between each element and at either end are tap points accessible to the wiper terminal.

The position of the wiper element is controlled by the CS, U/D, and INC inputs. The position of the wiper can be stored in non-volatile memory and then be recalled upon a subsequent power-up operation. The device can be used as a three-terminal potentiometer or as a two-terminal variable resistor in a wide variety of applications ranging from control to signal processing to parameter adjustment.

There are three sections of the Dc3v-5v X9c103s Digital Potentiometer as the input control, counter and decode section; the non-volatile memory; and the resistor array. The input control section operates just like an up/down counter. The output of this counter is decoded to turn on a single electronic switch connecting a point on the resistor array to the wiper output. Under the proper conditions, the contents of the counter can be stored in non-volatile memory and retained for future use. The resistor array is comprised of 99 individual resistors connected in series. At either end of the array and between each resistor is an electronic switch that transfers the potential at that point to the wiper.

The wiper, when at either fixed terminal, acts like its mechanical equivalent and does not move beyond the last position. That is, the counter does not wrap around when clocked to either extreme. The electronic switches on the device operate in a “make-before-break” mode when the wiper changes tap positions. If the wiper is moved several positions, multiple taps are connected to the wiper for tIW (INC to VW/RW change). The TOTAL value of the device can temporarily be reduced by a significant amount if the wiper is moved to several positions. When the device is powered-down, the last wiper position stored will be maintained in the non-volatile memory.
When power is restored, the contents of the memory are recalled and the wiper is reset to the value last stored. The internal charge pump allows a wide range of voltages (from -5V to 5V) applied to XDCP terminals yet given a convenience of the single power supply. The typical charge pump noise of 20mV at 850kHz should be taken into consideration when designing an application circuit.


Specifications and Features

  • Simple 3 pin interface to control the resistance!
  • Supply voltage: 3V-5V
  • Chip: X9C103S
  • PCB board size: 2.7 * 1.3CM
  • 10K span potentiometer.
  • Potentiometer center tap between 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
  • VL and VH digital potentiometer sliding rheostat port corresponding to the low-end and high-end, allowing the input voltage range -5V to + 5V.


Package includes 1 x Dc3v-5v X9c103s Digital Potentiometer Module for Arduino

Related Links

Reviews (0)

Write a review

Note: HTML is not translated!
    Bad           Good

NEW Products

Product Page : New Products

VL6180X Distance Sensor Module

VL6180X Distance Sensor Module

VL6180X Distance Sensor ModuleVL6180X Time of Flight Distance SensorThe VL6180X is a time-of-flight ..

Rs.623.04 (inc GST)

Nrf24l01 adaptor board 

Nrf24l01 adaptor board 

Nrf24l01 adaptor board Low cost Breakout board for NRF24L01 RF ModulesHaving problem interfacin..

Rs.82.60 (inc GST)

MPS20N0040D Pressure sensor

MPS20N0040D Pressure sensor

MPS20N0040D SensorMPS20N0040D MEMS Air Pressure Sensor.MPS20N0040D Air pressure sensor measures pres..

Rs.259.60 (inc GST)

T-Cobbler Plus for Raspberry Pi 2 & 3

T-Cobbler Plus for Raspberry Pi 2 & 3

T-Cobbler Plus for Raspberry Pi 2 and 3GPIO Extension Board for Raspberry Pi 3B and Raspberry Pi 3B ..

Rs.236.00 (inc GST)

Have You Seen

Product Page : Have You Seen

MAX 550 Micro Soldering Station

MAX 550 Micro Soldering Station

MAX 550 Micro Soldering StationThis is a prefect low cost solder station if you are looking to solde..

Rs.472.00 (inc GST)

Samsung 18650 2600mah Li-ion Battery

Samsung 18650 2600mah Li-ion Battery

Samsung ICR18650-26J 2.6Ah BatteryOriginal Samsung 18650 2600 mah Lithium-ion BatteryThis is or..

Rs.275.00 (inc GST)

SPDT 2 way Toggle Switch  (ON-ON)

SPDT 2 way Toggle Switch (ON-ON)

SPDT 3 Pin 2 Way Toggle SwitchMTS102 Single Pole Double throw (SPDT) ON-ON type Panel Mounting switc..

Rs.22.42 (inc GST)

Arduino Mega 2560 Pro Mini

Arduino Mega 2560 Pro Mini

Mega Pro 2560 Development Board Mega 2560 Pro a  Atmega2560 based compact Arduino MegaThis..

Rs.973.50 (inc GST)

Related Products

MCP41010 8-Bit Digital Potentiometer

MCP41010 8-Bit Digital Potentiometer

MCP41010 8-Bit Digital PotentiometerThe MCP41010 is a single-channel, 8-bit digital potentiometer fe..

Rs.177.00 (inc GST)

X9C104 Digital Potentiometer Module

X9C104 Digital Potentiometer Module

X9C104 Digital Potentiometer ModuleThis Module is a breakout board for Intersils X9C104 digitally co..

Rs.295.00 (inc GST)